#Weatherpro power awning manual how to#
#Weatherpro power awning manual manual#
#Weatherpro power awning manual code#

Using a cloth and pliers to hold the left-hand awning bracket, you should be able to remove the pin and then add a winding or two to the spring before putting the pin back in and re-installing the bracket onto the arm. and remove the screw that holds the awning bracket to the left-hand arm. Then pin the left-hand end so it doesn’t unroll (leaving the right-hand side in “Extend” mode so the spring is ratcheted and won’t unwind on you).

Just unroll it a bit like at the beginning of the video. Hi Kenny! Sorry you had trouble! You shouldn’t need to completely undo and unroll the awning in order to add more tension. before it's perfect.Īnd if THAT doesn't do it, we'd suggest reaching out Tyler at Tough Top Awnings to see if he has any input (HE'S the expert on awnings!). It can take some repeated adjustments, roll the awning in/out, re-adjust. You just want to make sure that, once done, the fabric is centered on the roller tube (you can measure from the end cap to the edge of the fabric on each end of the roller to see how close they are). or pull the fabric at the attachment on the wall of the RV toward the arm where you saw the 'inverted cone' of fabric. With the awning extended, you can either pull the fabric on the tube toward the arm on the end where you could see the concentric rolls. If you see that, you need to pull the fabric so that it rolls up straight. When that happens, the fabric rolls up misaligned (when rolled up, on one end you'll see the concentric roll of the edge of the fabric, and on the other end it will be an 'inverted cone'). where one of the attachment points (side of RV or roller tube) got pulled forward/backward. Once the structure of the arm is confirmed, if you're still having the problem, it could be a result of the fabric being pulled out of square. We'd take a very close look at all elements on that rear arm and try to figure out if, when retracting the awning with the lock nut engaged, something got pushed/squished out of alignment. That could cause the arm to be at a different height when retracting, and thus having the fabric roll up on the roller tube incorrectly. We're not experts on the 9100 power awning, but it sounds like leaving the lock nut tight may have bent/misadjsted something on that back arm itself.

#Weatherpro power awning manual code#

Tough Top Awnings (Get a 5% Discount when you use code “ RVGEEKSROCK” at checkout online or on the phone) – NOTE: the straight pick we used to pin the roller tube is available from Tough Top… so order one with your replacement fabric!.

#Weatherpro power awning manual how to#

How To Replace an RV Patio Awning (Original Version).All of our Awning & Slide Topper Replacement Videos.Save 5% on your entire order by using Discount Code RVGEEKSROCK at checkout! View our entire awning & slide topper replacement playlist.Ĭomplete details on measuring and ordering replacement slide topper and awning fabric are available at.

Of course Tom & Cait were rolling cameras too, so you can check out their version of the installation here:īe sure to check out the Morton’s website and YouTube channel for lots of other great content:ĭo you have a different model awning, or want to replace your slide topper fabric? Watch the video above to see how surprisingly easy this job is for any reasonably competent DIY RVer (with the help of a couple of friends)! Since we’ve gotten positive feedback whenever we’ve included bloopers, look for a few at the end. Here’s a step-by-step tutorial, as we replace the awning on our friends Tom & Cait Morton’s 5th wheel. We’ve now learned a new way to do the job… a considerably easier method than the old way.

#Weatherpro power awning manual manual#

A few years ago, we showed how to replace one of the most popular patio awnings on the market – the manual pull-down Dometic/A&E. We’ve demonstrated how to replace the fabric on many different awning & slide topper models.